Hi-Lo Street Roller Hockey Wheels (4-Pack)

About the Hi-Lo Street Roller Hockey Wheels (4-Pack)

The Hi-Lo Street wheel system is engineered around a height differential that positions 80 mm wheels at the front axles and 76 mm wheels at the rear, lowering the skater's centre of gravity by approximately 4 mm while maintaining forward rolling efficiency. Each wheel is compounded at 82A durometer, a hardness calibrated for asphalt, sport-court tiles, and the sealed concrete surfaces common at facilities such as the ice rinks in India. The 82A rating resists premature flat-spotting on abrasive Indian street and rink surfaces while retaining enough grip for sharp crossover cuts. The urethane core is precision-moulded to accept standard 608 bearings, keeping bearing seating concentricity within ±0.05 mm for minimal vibration transfer. The 4-pack format covers a full set of front or rear wheels, enabling targeted rotation schedules that extend overall wheel life. Developed with surface-condition data from Bengaluru-based R&D testing, the Hi-Lo Street wheel addresses the high-temperature, grit-laden conditions characteristic of South Asian inline play.

Overview

Hi-Lo Height System

The 4 mm differential between front and rear wheels shifts the skater's centre of gravity rearward, improving edge engagement during quick-stop manoeuvres and reducing ankle fatigue on prolonged street sessions across hard Indian court surfaces.

• 80 mm front wheels maximise forward stride length
• 76 mm rear wheels lower centre of gravity by 4 mm
• Optimised for Hi-Lo chassis found on most inline hockey skates
• Consistent geometry across all four moulded urethane wheels

82A Street Durometer

At 82A, the urethane compound is firm enough to resist flat-spotting on grit-laden asphalt and sport-court tile common across Indian inline facilities, while delivering sufficient traction for lateral cuts and aggressive play in warm, high-humidity conditions.

• 82A hardness rated for asphalt and sealed concrete
• Resists heat-induced deformation above 35 °C ambient
• Grip-to-glide balance suited for indoor and outdoor rinks
• Reduced flat-spot risk on abrasive South Asian surfaces

Hi-Lo Street Roller Hockey Wheels (4-Pack) specifications

Key features

• Differential Geometry — The 80 mm / 76 mm pairing is not cosmetic — the 4 mm drop shifts weight distribution rearward, replicating ice-skate blade geometry on inline frames and reducing forward lean fatigue during extended street sessions.
• 82A Urethane Compound — The urethane formulation is balanced at 82A to resist premature wear on abrasive surfaces while maintaining edge-load grip. Tested at ambient temperatures up to 40 °C, relevant to outdoor inline play in Indian summers.
• 608 Bearing Compatibility — The precision-moulded core accepts any standard 608 bearing (22 mm OD, 8 mm ID) with a seating tolerance of ±0.05 mm, minimising lateral play and vibration across all skating speeds.
• Rotation-Ready Design — Uniform urethane density across all four wheels allows systematic front-to-rear rotation at every 10–15 hours of ice time, extending pack lifespan and maintaining consistent rolling performance throughout the wheel's service life.
• Low-Vibration Core — Concentric bearing bore machining within ±0.05 mm reduces micro-vibration at the boot cuff, protecting ankle joints during repeated hard stops — a critical factor on the uneven court-tile surfaces found at many Indian inline venues.
• Bengaluru R&D Validation — Wheel geometry and compound hardness were validated using surface-condition data gathered at indoor and outdoor rinks in Bengaluru, ensuring performance targets reflect actual Indian climate and surface variables, not solely temperate-zone laboratory conditions.
• Frame Compatibility — Designed for Hi-Lo inline hockey chassis with standard 80/76 mm wheel pockets. Compatible with leading 4-wheel inline hockey skate frames available in the Indian market, requiring no spacer modification or axle adaption.

Hi-Lo Street Roller Hockey Wheels (4-Pack) size guide

Roller hockey wheels are chosen by diameter (in mm) and hardness (the "A" number). The easiest way: check the numbers printed on your current wheels and buy the same.

How to measure

1. Look at the side of your current wheels — you will see a size like 76mm or 80mm and a hardness like 74A or 82A.
2. Order the same diameter. Most hockey frames use two sizes (Hi-Lo): smaller wheels at the front, bigger at the back.
3. Choose hardness by surface (see below).

Typical wheel sizes by skate size

• Hardness: a lower number (74A–76A) is softer and grips better indoors on smooth floors. A higher number (82A+) is harder and lasts longer outdoors on rough concrete.
• A full set for one pair of 4-wheel skates is 8 wheels.
• Never fit a wheel bigger than your frame allows — it will rub.
• Not sure? Message us on WhatsApp (+91 91112 22274) with your measurements and we will confirm the right size before you order.

Typical Hi-Lo setups from Alkali and Bauer frames. Your frame may differ — check your current wheels.

How it compares

Hi-Lo Street Roller Hockey Wheels (4-Pack) vs Bauer Hi-Lo Street Wheels

Hi-Lo Street Roller Hockey Wheels (4-Pack) vs CCM Outdoor Wheels (Single Diameter)

Hi-Lo Street Roller Hockey Wheels (4-Pack) — frequently asked questions

What is the difference between the 80 mm and 76 mm Hi-Lo Street wheels?

The 80 mm wheels are installed at the front axle positions on a Hi-Lo chassis, providing a longer stride arc and greater top-end rolling speed. The 76 mm wheels sit at the rear axle positions, lowering the skater's centre of gravity by 4 mm. Together they replicate the angled blade geometry of ice skates, improving edge control and balance.

Is 82A the correct hardness for Indian indoor rinks and outdoor street courts?

Yes. At 82A, the urethane compound is calibrated for hard, abrasive surfaces including sealed concrete, sport-court tile, and asphalt — the surface types most common at Indian inline hockey venues. Softer wheels (72A–78A) are better for smooth sport-court only; 82A resists flat-spotting on the grit and heat conditions typical of South Asian outdoor and semi-outdoor rinks.

What bearings are compatible with Hi-Lo Street wheels?

Hi-Lo Street wheels accept any standard 608-size bearing, which has a 22 mm outer diameter and 8 mm inner diameter bore. ABEC-5 or ABEC-7 rated 608 bearings are recommended for inline hockey at this wheel hardness, as they balance speed and durability without requiring frequent replacement.

How many packs do I need to replace all wheels on my inline skates?

A full wheel replacement on a standard 4-wheel Hi-Lo inline hockey skate (one pair of skates, 8 wheels total) requires two 4-packs — one in the 80 mm 82A configuration for front axle positions on both skates, and one in the 76 mm 82A configuration for rear axle positions on both skates.

How often should I rotate or replace Hi-Lo Street wheels on Indian street surfaces?

On abrasive asphalt or grit-covered outdoor surfaces common across Indian cities, inspect wheels every 8–10 hours of skating. Rotate front-to-rear at approximately 10–15 hours to equalise wear. Replace when the wheel diameter has reduced by more than 3 mm from its original measurement or when flat spots are visible affecting straight-line tracking.

Can I mix 80 mm and 76 mm wheels from different brands on a Hi-Lo chassis?

Technically possible if the bearing bore is standard 608 size, but inadvisable for competitive play. Mixing urethane compounds of different hardness and density across axle positions creates uneven grip-and-glide ratios, increasing ankle stress. For consistent performance, use matched wheels from the same compound batch across each axle position.

Are Hi-Lo Street wheels suitable for the ASICS rink surface in Bengaluru?

The 82A durometer is appropriate for the sealed sport-court surface at the ASICS inline hockey rink in Bengaluru. The compound resists the heat-accelerated softening that can cause lower-durometer wheels to flat-spot in Bengaluru's warm ambient temperatures, while still providing adequate grip for lateral cutting on smooth indoor tiles.

Do Hi-Lo Street wheels work with ice hockey skate boots converted to inline use?

Yes, provided the conversion chassis accepts 80 mm and 76 mm wheel pockets in Hi-Lo configuration and uses standard axle hardware. The 608 bearing bore is universal across inline conversion frames. Verify your specific chassis manufacturer's wheel height specifications before purchasing to confirm diameter compatibility.